Battery Packs for Surgical and Medical Robot Systems
A surgical robot battery must keep power steady through a procedure, report its state at all times and fail safely. Jetray designs custom lithium packs for medical robot makers. Because requirements here are strict, we review each project against your specification before we commit.

Recommended products
Packs and cells we supply for this application. Every model can be customized — tap + to add models to your inquiry list, then send one request for all of them.
Try removing a filter — or tell us your spec and we will build it for you.
What robot makers ask of the battery

- No power glitches. A short drop can cause erratic movement, so many systems add a battery as a backup source on the supply path.
- Known state. The system reads charge level, voltage, current, temperature and faults from the BMS.
- Safe failure. The pack cuts off before a cell leaves its safe range, and says why.
- Predictable run time. The robot needs to know how long it can work.
- Traceable documents. Buyers ask for test reports and change control.
Where the pack sits in the system
Sterilisation is a major design point. Some tool packs are removed before sterilising, and some must withstand it. If your tool pack must withstand sterilisation, send the method and cycle count, and we design and test the samples for it.
What we can do
- 01Cells LiFePO4 for long life and stability, or Li-ion for energy density. Cell selection →
- 02BMS protection against overcharge, over-discharge, over-current, short circuit and high temperature, set from your load and confirmed on samples. BMS design →
- 03Communication CAN, UART, RS485 and Bluetooth, set up to your requirement.
- 04Charger a matching charger.
- 05Enclosure plastic or sheet metal, IP65 as our usual level and other levels on request. Enclosure design →
- 06Backup power path we can design the power path and switch-over for a backup role, as well as the pack.
- 07Test equipment we test samples on our own equipment and share the results.
Documents
UN38.3, IEC 62133 and MSDS documents are available, with transport and certification reports for the shipment.
Medical device rules depend on your device and market, and we do not claim a medical quality-system certificate. Tell us the standards your design must meet, and we say plainly which ones we can support. Quality and certification →

How to start
- 01Send the system voltage, peak and average current, run time and the backup role of the battery.
- 02We reply with questions and a first proposal.
- 03We build samples. Custom battery pack samples are charged.
- 04You test the samples in the system. Custom packs usually take one to two months.
What to agree early on a surgical robot battery
Which part is battery-powered
TAP TO SEE WHYBackup role
TAP TO SEE WHYData
TAP TO SEE WHYDocuments your customer needs
TAP TO SEE WHYProject scope
TAP TO SEE WHYOptions you can set
Mark what you want to discuss. Your picks go into the quote form below.
From first message to delivery
Send the system type, load, backup time and space available.
We tell you whether we can take the project, and propose the pack.
We build a charged sample, and you test it in the system.
We adjust from your results.
Batch production, final test and shipment with the documents you need.
Frequently asked questions
Send the sterilisation method and cycle count. We design the pack for it and test the samples.
Yes, this is a common design. We size the cells and protection for the switch-over and standby needs you give us.
Yes. CAN, UART, RS485 and Bluetooth can be set up to your requirement.
UN38.3, IEC 62133 and MSDS. Medical device rules depend on your device and market.
It depends on the product. Send your quantity and we confirm.
Not always. We review each project, and tell you honestly if it is a fit.
We have our own test equipment and can provide transport and certification reports.
Designing a medical robot?
Send the voltage, current and backup role. We reply within 24 hours.
Your surgical robot battery packs
Values from the tools above are already here. Add what you know and send.
Your message to an engineer
Fill what you know. Blank lines are fine.Goes straight to our sales engineers, the same as the quote form. Need to attach a drawing? Use the quote form or email it.
Designing a medical robot? Send the voltage, current and backup role.
Request a Quote→










































































