
Custom Battery Packs for Electric Motorcycles and Dirt Bikes
An electric motorcycle battery must give high peak current, take hard vibration and shed heat. Jetray builds custom Li-ion packs for electric motorcycle and dirt bike makers, to your voltage, controller and frame.
Recommended products
Packs and cells we supply for this application. Every model can be customized — tap + to add models to your inquiry list, then send one request for all of them.
Try removing a filter — or tell us your spec and we will build it for you.
What decides the pack
- 01Voltage. 48 V to 100 V and above, set by the motor and controller.
- 02Peak current. Acceleration and climbing draw hundreds of amps in the largest packs. The cells, busbars and BMS must carry it.
- 03Heat. High current warms the pack, so layout and temperature sensing matter.
- 04Vibration and shock. Off-road riding is hard on welds, connectors and cases.
- 05Weight and balance. The pack is a large share of the vehicle's mass.
Voltage by cell count
Capacity (Ah) comes from cells in parallel, and the discharge rate of the cell sets peak current. Send your controller's current limit. Cell selection →
Cells and build

- Cells high-discharge 21700 or 18650 Li-ion, chosen by peak current and heat. Brands we can offer include Panasonic, Samsung, LG, Molicel and EVE.
- Structure cell holders, busbars and wiring sized for the current, with vibration in mind. Busbar designs for continuous currents above 300 A are available.
- Case sheet metal or plastic, IP65 as our usual level and other levels on request. Sheet metal helps with heat and knocks. Enclosure design →
- BMS protection against overcharge, over-discharge, over-current, short circuit and high temperature. BMS design →
- Communication CAN, UART and Bluetooth, set up to your requirement. Charger and communication →
- Charger a matching charger.
Documents and shipping

UN38.3, IEC 62133 and MSDS documents are available, with transport and certification reports for the shipment. High-voltage packs may be classed differently for transport. Tell us the voltage and energy at the start. Other standards depend on the market. Quality and certification →
Order and delivery
Custom battery pack samples are charged, and you test them on your bike. Custom packs usually take one to two months. MOQ depends on the product. We support private label and supply distributors. Prototyping and samples → OEM, ODM and private label →

Mistakes to avoid on high-power bike packs
Underrating peak current
Hard acceleration draws very high current. Cells, welds and wiring must carry it.
Heat
High current warms the pack. Give us the airflow and mounting space.
Vibration
Off-road riding shakes the pack. The internal build and case must resist it.
Water and mud
Choose the sealing level for where the bike rides.
Controller mismatch
The BMS must match the controller's limits and signals.
Options you can set
Mark what you want to discuss. Your picks go into the quote form below.
From first message to delivery
STEP 1Send the motor, controller, battery space and target range and speed.
STEP 2We propose the cell layout, BMS and case, and quote.
STEP 3We build a charged sample, and you test it on a bike.
STEP 4We adjust the build or BMS limits from your test notes.
STEP 5Batch production, final test and worldwide shipping.
Frequently asked questions
Common values are 48 V, 60 V and 72 V, with higher voltage in performance bikes. The controller decides.
High-discharge 21700 or 18650 Li-ion cells. The right cell depends on peak current and heat.
Send the frame drawing or photos and the connector. We propose the case and layout.
Send the model and its specification. We confirm on a sample whether we can match it.
CAN, UART and Bluetooth can be set up to your requirement.
We size the cells, welds and BMS for the peak current you give us, and confirm on a sample.
Yes. Private label is supported.
Building an e-moto?
Send the voltage, peak current and frame space. We reply within 24 hours.
Your electric motorcycle and dirt bike packs
Values from the tools above are already here. Add what you know and send.
Your message to an engineer
Fill what you know. Blank lines are fine.Goes straight to our sales engineers, the same as the quote form. Need to attach a drawing? Use the quote form or email it.
Building an e-moto? Send the voltage, peak current and frame space.
Request a Quote→



































































